3.2L Ultrasonic Gun Cleaner 100W 20-80C Adjutable For Bullet Case

3.2 Liter 100W Ultrasonic Power Ultrasonic Gun Cleaner For Bullet Case

Ultrasonic Cleaning--How to Get the Best Results?

Reader "Gunamonth" has a great deal of experience with ultrasonic cleaning methods, perfecting his skills on small 17-caliber cases that are very difficult to clean with conventional brushing or tumbling. Here are his tips for getting better, faster results from your ultrasonic cleaning sessions.

Whale Cleen 's Ultrasonic Cleaning Tips
I thought it might be helpful to understand some of the principles involved and maybe how to stay out of trouble. I've noted that some members have observed that their brass comes out "too clean" or has a rough surface when finished. Here are some ways to avoid those potential problems.

The Chemistry
Both metals used in brass cases (copper and zinc) are soluble in acetic acid (vinegar). The salts, copper acetate and zinc acetate, are also soluble. Zinc is more soluble than copper so it dissolves faster. In addition a galvanic action occurs that cause copper to be dissolved and then redeposited on the surface at the expense of the zinc.

When you clean brass cases in a vinegar solution you change both the chemical and physical properties of the surface of the case. There have been comments about cases being too clean, primers hard to seat, deposits on mandrels, etc. When you change the surface by dissolving some of it and etching it these things will happen. Whether they happen to the point of being a problem becomes the issue.

This doesn't mean that you shouldn't use acetic acid or that there is anything wrong with Jason's approach. Anything used to clean brass chemically is going to have some effect on the surface and it sure beats trying to get residue out of the flash hole of a 17 Remington with a brush.

Beaker Selection
I suggest you use one beaker and make it the largest you can fit in your ultrasonic unit. This gives more surface area for the tank water to work on and reduces the attenuation the beaker causes. Also, if you're in the market for beakers look for Kimax brand rather than Pyrex. Kimax is about 30% thinner and attenuates the ultrasound less.

How to Achieve Better Results
To minimize the effect on the brass there are some things you can do, most of which attempt to reduce the amount of time the cases spend in the acetic acid:

1. Keep the cleaning solution cool. In other words don't use hot water to mix up the vinegar solution. My ultrasonic tank is in the garage which isn't air conditioned so when I use it in the summer I empty the tank and fill it with cold water.

2. Clean a rather small number of cases at a time. I do about fifteen 17 Remingtons at a time. They're as clean as they're gonna' get in less than four minutes. I've tried as many as 100 at a time and it takes a very long time. Brass is pretty good at absorbing ultrasonic energy and too many cases translates to too little energy per case to clean quickly.

3. Keep the cleaning system "tuned". The unit I have has a tank that is about 5X10X5 inches. I cut a piece of Plexiglas to cover it and cut a hole the size of a 600ml beaker with a fly cutter. I made a collar for the beaker out of plastic foam that fits very snugly so the beaker can be raised or lowered. By adjusting the level of water in the tank, liquid in the beaker and depth of the beaker in the water it can be "tuned" so that the liquid in the beaker appears to boil while the water in the tank is calm. It only takes a few minutes and has a major effect on how long it takes to get them clean.

4. Don't let the beaker touch the any part of the tank, especially the bottom where the transducer is. The idea is to cause the brass to oscillate, not the container.

Specification:

Cleaning Feedback Of Bullet Case:

3.2L Ultrasonic Gun Cleaner

Bullet Case Ultrasonic Gun Cleaner

100W Ultrasonic Bullet Case Cleaner

3.2L Ultrasonic Gun Cleaner 100W 20-80C Adjutable For Bullet Case Images